ทดสอบ ตู้กรองแดดบ้านหินธานีโมเดล ไฟเอซีโมดุลย์โนเวม ..11 แอมป์ .โดยใช้ คอยล์มอเตอร์ซืงเกิ้ลเฟส 1/4 แรงม้า ซิงเกิ้ลเฟส นำคอยล์ สตาร์ทและ คอยล์รัน มา ต่อนุกรมกัน แล้ว ผ่าน คาปา 4.5 ไมโครฟารัด 400 โวลท์ ..ทีวีใสปิ่ง..
มีข้อน่าสังเกต ..ว่า การปรับค่าพาวเวอร์แฟคเตอร์ให้ใกล้เคียง 0.9 จะทำให้ระบบ กินกระแส และ กำลังวัตต์น้อยลง ..กว่า ค่าพาวเวิร์แฟคเตอร์ต่ำ ..ซึ่ง ตามทฤษฎี ค่ากำลังวัตต์ = กระแส x แรงดัน x power factor
ดังนั้น ค่าที่ ควรวัด และ ปรับปรุง ในระบบ ไฟฟ้าในบ้าน ของแต่ละอุปกรณ์ไฟฟ้า ..คิ ค่าพาวเวอร์แฟคเตอร์ ..ที่จะช่วยให้ลดค่าใช้จ่ายค่าไฟแอบแฝง..ที่แพงโดยไม่มีเหตุผล ../ลุงนันท์ และ อ. บุญเหลือ ทดสอบ ..เรื่องนี้จะนำไปสอน ที่ งาน โซลาร์คณธรรม ครั้งที่ 3 ที่ศูนย์เนท สุรินทร์ ด้วย ..ครับ พี้น้อง ...!
In electrical engineering, the power factor of an AC electrical power system is defined as the ratio of the real power flowing to the load to the apparent power in the circuit, and is a dimensionless number in the closed interval of −1 to 1. A power factor of less than one means that the voltage and current waveforms are not in phase, reducing the instantaneous product of the two waveforms (V × I). Real power is the capacity of the circuit for performing work in a particular time. Apparent power is the product of the current and voltage of the circuit. Due to energy stored in the load and returned to the source, or due to a non-linear load that distorts the wave shape of the current drawn from the source, the apparent power will be greater than the real power. A negative power factor occurs when the device (which is normally the load) generates power, which then flows back towards the source, which is normally considered the generator.
In an electric power system, a load with a low power factor draws more current than a load with a high power factor for the same amount of useful power transferred. The higher currents increase the energy lost in the distribution system, and require larger wires and other equipment. Because of the costs of larger equipment and wasted energy, electrical utilities will usually charge a higher cost to industrial or commercial customers where there is a low power factor.
Linear loads with low power factor (such as induction motors) can be corrected with a passive network of capacitors or inductors. Non-linear loads, such as rectifiers, distort the current drawn from the system. In such cases, active or passive power factor correction may be used to counteract the distortion and raise the power factor. The devices for correction of the power factor may be at a central substation, spread out over a distribution system, or built into power-consuming equipment.
More../click/
1 Linear circuits
1.1 Definition and calculation
1.2 Power factor correction of linear loads
2 Non-linear loads
2.1 Non-sinusoidal components
2.2 Distortion power factor
2.3 Distortion in three-phase networks
2.4 Switched-mode power supplies
2.5 Power factor correction (PFC) in non-linear loads
2.5.1 Passive PFC
2.5.2 Active PFC
2.5.3 Dynamic PFC
3 Importance of power factor in distribution systems
4 Techniques for measuring the power factor
5 Mnemonics
6 References
7 External links
เครดิต : https://www.facebook.com/Dakkini/?ref=page_internal
https://en.wikipedia.org/wiki/Power_factor
ไม่มีความคิดเห็น:
แสดงความคิดเห็น